d*******n
发帖数: 369 | 1 Title: Remote Access to Admin Web GUI
I've been trying this for 2 weeks. no luck. I looked at almost all related
posts here but still couldn't get mine to work.
Local access works when I point my browser to the local router IP of 192.168
.2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
com).
I am trying to get remote access working and when I point a remote browser
to example.homelinux.com:8080 or my.real.internet.ip:8080, nothing comes up.
My network settings:
I guess the complexity of my case is from the cable modem. Motorola SBG900.
It comes with router functionality although I need it to be modem only. I
disabled its NAT but its DHCP cannot be disabled so it got an IP 192.168.0.1
and assigned an IP (192.168.0.2) to my router A.The router A's WAN is wired
to the modem.
I have two routers (A and B) loaded with Tomato 1.28 as listed below. They
are connected wirelessly via WDS. As an experiment, when I enable Remote
access of Admin on this MODEM, I can access it remotely. It's currently
disabled since what I want is the admin access of my router A.
Router A (Asus RT-N16, Gateway) :
Under Administration > Admin Access > Web Admin, I have the following
setttings:
Remote Access: checked and HTTP
Port: 8080
Allow Wireless Access: checked
Note that the WAN of this router can get the internet (outside) IP address.
Under Port Forwarding I have the following settings:
Proto: Both
Src Address: /blank/
Ext Ports: 8080
Int Port: 80
Int Address: 192.168.2.1
Router B (Linksys E3000, Router, wirelessly WDS with Router A) :
This router is AP only.
Both Gateway and DNS point to Router A (192.168.2.1).
I want to access the Admin GUI of router A remotely but I can't no matter
how hard I tried. I even tried that via OpenVPN. It barely works, a lot of
timeout. It sometime shows GUI partially after several refresh (F5).
Really frustrating! Please help. 给任何帮我解决问题的牛哥。 |
f*******5
发帖数: 10321 | 2 why did you disable nat on the modem?
168
up.
.
【在 d*******n 的大作中提到】
: Title: Remote Access to Admin Web GUI
: I've been trying this for 2 weeks. no luck. I looked at almost all related
: posts here but still couldn't get mine to work.
: Local access works when I point my browser to the local router IP of 192.168
: .2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
: com).
: I am trying to get remote access working and when I point a remote browser
: to example.homelinux.com:8080 or my.real.internet.ip:8080, nothing comes up.
: My network settings:
: I guess the complexity of my case is from the cable modem. Motorola SBG900.
|
g***u
发帖数: 5413 | 3 its DHCP cannot be disabled
Why?
Title: Remote Access to Admin Web GUI
I've been trying this for 2 weeks. no luck. I looked at almost all related
posts here but still couldn't get mine to work.
Local access works when I point my browser to the local router IP of 192.168
.2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
com).
I am trying to get remote access working and when I point a remote browser
to example.homelinux.com:8080 or my.real.internet.ip:8080, nothing comes up.
My network settings:
I guess the complexity of my case is from the cable modem. Motorola SBG900.
It comes with router functionality although I need it to be modem only. I
disabled its NAT but its DHCP cannot be disabled so it got an IP 192.168.0.1
and assigned an IP (192.168.0.2) to my router A.The router A's WAN is wired
to the modem.
I have two routers (A and B) loaded with Tomato 1.28 as listed below. They
are connected wirelessly via WDS. As an experiment, when I enable Remote
access of Admin on this MODEM, I can access it remotely. It's currently
disabled since what I want is the admin access of my router A.
Router A (Asus RT-N16, Gateway) :
Under Administration > Admin Access > Web Admin, I have the following
setttings:
Remote Access: checked and HTTP
Port: 8080
Allow Wireless Access: checked
Note that the WAN of this router can get the internet (outside) IP address.
Under Port Forwarding I have the following settings:
Proto: Both
Src Address: /blank/
Ext Ports: 8080
Int Port: 80
Int Address: 192.168.2.1
Router B (Linksys E3000, Router, wirelessly WDS with Router A) :
This router is AP only.
Both Gateway and DNS point to Router A (192.168.2.1).
I want to access the Admin GUI of router A remotely but I can't no matter
how hard I tried. I even tried that via OpenVPN. It barely works, a lot of
timeout. It sometime shows GUI partially after several refresh (F5).
Really frustrating! Please help. 给任何帮我解决问题的牛哥。
【在 d*******n 的大作中提到】
: Title: Remote Access to Admin Web GUI
: I've been trying this for 2 weeks. no luck. I looked at almost all related
: posts here but still couldn't get mine to work.
: Local access works when I point my browser to the local router IP of 192.168
: .2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
: com).
: I am trying to get remote access working and when I point a remote browser
: to example.homelinux.com:8080 or my.real.internet.ip:8080, nothing comes up.
: My network settings:
: I guess the complexity of my case is from the cable modem. Motorola SBG900.
|
d*******n
发帖数: 369 | 4 I want the modem to be a modem. With NAT enabled, the modem will get the WAN
ip address and acts as a gateway.
【在 f*******5 的大作中提到】
: why did you disable nat on the modem?
:
: 168
: up.
: .
|
d*******n
发帖数: 369 | 5 That's how the modem's made. Nowhere to disable it.
168
up.
【在 g***u 的大作中提到】
: its DHCP cannot be disabled
: Why?
:
: Title: Remote Access to Admin Web GUI
: I've been trying this for 2 weeks. no luck. I looked at almost all related
: posts here but still couldn't get mine to work.
: Local access works when I point my browser to the local router IP of 192.168
: .2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
: com).
: I am trying to get remote access working and when I point a remote browser
|
g***u
发帖数: 5413 | 6 google一下，还真是
你试试这个看看
http://micolous.id.au/archives/2008/03/24/motorola-surfboard-dh
【在 d*******n 的大作中提到】
: That's how the modem's made. Nowhere to disable it.
:
: 168
: up.
|
f*******5
发帖数: 10321 | 7 if you dont set port-forwarding in the modem, how does it know where to
relay to incoming requests?
【在 d*******n 的大作中提到】
: That's how the modem's made. Nowhere to disable it.
:
: 168
: up.
|
t****t
发帖数: 6806 | 8 你这说得一片混乱啊, 我来猜猜, 你回答是或不是
1. router A被modem设成DMZ了?
2. router A的LAN IP是192.168.2.1? 如果不是, 192.168.2.1是谁?
3. router A的从modem分配的IP是192.168.0.2, 但是自己能看到modem的WAN IP?
4. modem的remote access如果打开, 可以从外面访问? 端口是多少, 80吗?
5. 你要访问router A的GUI, 你打开了web admin remote access, 并且端口是8080?
6. 你在A上设了port forwarding, 从8080到192.168.2.1的80?
最后你试一下把A的port forwarding关掉.
168
up.
.
【在 d*******n 的大作中提到】
: Title: Remote Access to Admin Web GUI
: I've been trying this for 2 weeks. no luck. I looked at almost all related
: posts here but still couldn't get mine to work.
: Local access works when I point my browser to the local router IP of 192.168
: .2.1 or the DDNS address of example.homelinux.com:8080 (belongs to dyndns.
: com).
: I am trying to get remote access working and when I point a remote browser
: to example.homelinux.com:8080 or my.real.internet.ip:8080, nothing comes up.
: My network settings:
: I guess the complexity of my case is from the cable modem. Motorola SBG900.
|
d*******n
发帖数: 369 | 9
Ans: Yes.
Ans: Yes. router A的LAN IP就是192.168.2.1
Ans: 以下是从Tomato Status Overview copy/paste 过来的。另外在moto SBG900
modem的Admin GUI上显示router A的IP是192.168.0.2
=============== WAN ========================
Connection Type DHCP
IP Address 71.59.2x.xx
Subnet Mask 255.255.248.0
Gateway 71.59.xx.xx
DNS 75.75.75.75:53, 75.75.76.76:53
Status Connected
Connection Uptime 0 days, 00:05:55
Remaining Lease Time 2 days, 16:52:22
================ LAN ==================
Router MAC Address BC:AE:C5:C3:1A:39
Router IP Addresses 192.168.2.1/24 on LAN (br0)
DHCP 192.168.2.10 - 192.168.2.151 on LAN (br0)
Ans: yes 是80 for the modem的remote access
Ans: 是。我一打开GUI马上问我要user,pwd.我以为成功了。login输入后，就timeout
了。再Refresh(f5).browser显示 transfering data但马上变成"connecting to xxxx"
然后timeout.再refresh好几遍，勉强出来一部分GUI.和我用OpenVPN一个德行。我用
的是Tomato 1.28 Shibby build.
Ans: 是
试过了。和在Ans to 问题5一样。refresh好几遍，timeout。。。
【在 t****t 的大作中提到】
: 你这说得一片混乱啊, 我来猜猜, 你回答是或不是
: 1. router A被modem设成DMZ了?
: 2. router A的LAN IP是192.168.2.1? 如果不是, 192.168.2.1是谁?
: 3. router A的从modem分配的IP是192.168.0.2, 但是自己能看到modem的WAN IP?
: 4. modem的remote access如果打开, 可以从外面访问? 端口是多少, 80吗?
: 5. 你要访问router A的GUI, 你打开了web admin remote access, 并且端口是8080?
: 6. 你在A上设了port forwarding, 从8080到192.168.2.1的80?
: 最后你试一下把A的port forwarding关掉.
:
: 168
|
t****t
发帖数: 6806 | 10 听上去你remote access本身有问题, 你在家里能remote access吗? 我的意思是把A单
独放个子网, 并从WAN端口访问A的GUI
【在 d*******n 的大作中提到】
:
: Ans: Yes.
: Ans: Yes. router A的LAN IP就是192.168.2.1
: Ans: 以下是从Tomato Status Overview copy/paste 过来的。另外在moto SBG900
: modem的Admin GUI上显示router A的IP是192.168.0.2
: =============== WAN ========================
: Connection Type DHCP
: IP Address 71.59.2x.xx
: Subnet Mask 255.255.248.0
: Gateway 71.59.xx.xx
|
|
|
d*******n
发帖数: 369 | 11 我在家里（LAN）上可以用DDNS或WAN的裸IP带着port访问。no problem. 但是一用外网
，就好象用东西塞住了似的。刷好几遍才能load一部分GUI。我刚才又研究了一下modem
.把它设成了真正的NAT Passthru. 现在Router A is listed on the Passthrough Host Table of the
modem. 按照以下的定义现在modem真是modem only了。我也看不到router A在modem上
IP了。modem也显示DHCP disabled 了. 这样Router A 实际上直接和ISP接吻了。可还是不成。俺也是EE的技术民工。不过不是专稿网络的。实在没辙了，才来求教高手。
These are bridged CPEs, that have obtained their public IP address directly
from the DHCP server on your ISPs network, and are not using any form of
address translation.
先从10个包子。辛苦辛苦。
【在 t****t 的大作中提到】
: 听上去你remote access本身有问题, 你在家里能remote access吗? 我的意思是把A单
: 独放个子网, 并从WAN端口访问A的GUI
|
a*o
发帖数: 19981 | 12 你提供的信息自相矛盾啊，感觉你基本上是个网盲。。。
it got an IP 192.168.0.1 and assigned an IP (192.168.0.2) to my router A. -
this means your router A WAN IP should be 192.168.0.2
Router A (Asus RT-N16, Gateway) :
Note that the WAN of this router can get the internet (outside) IP address.
..... 怎么可能？
你一个WAN port还能给你俩地址？你到底插了几条线到modem那个router里？
你不会是同时接了个LAN port外加一个WAN port吧？ |
d*******n
发帖数: 369 | 13 正如前面所说，把modem变成modem only后，router A的WAN IP就是internet IP了，
and only the one.
-
.
【在 a*o 的大作中提到】
: 你提供的信息自相矛盾啊，感觉你基本上是个网盲。。。
: it got an IP 192.168.0.1 and assigned an IP (192.168.0.2) to my router A. -
: this means your router A WAN IP should be 192.168.0.2
: Router A (Asus RT-N16, Gateway) :
: Note that the WAN of this router can get the internet (outside) IP address.
: ..... 怎么可能？
: 你一个WAN port还能给你俩地址？你到底插了几条线到modem那个router里？
: 你不会是同时接了个LAN port外加一个WAN port吧？
|
t****t
发帖数: 6806 | 14 这个倒不是他网盲, 现在的DMZ都是这么设置的. 你out了.
-
.
【在 a*o 的大作中提到】
: 你提供的信息自相矛盾啊，感觉你基本上是个网盲。。。
: it got an IP 192.168.0.1 and assigned an IP (192.168.0.2) to my router A. -
: this means your router A WAN IP should be 192.168.0.2
: Router A (Asus RT-N16, Gateway) :
: Note that the WAN of this router can get the internet (outside) IP address.
: ..... 怎么可能？
: 你一个WAN port还能给你俩地址？你到底插了几条线到modem那个router里？
: 你不会是同时接了个LAN port外加一个WAN port吧？
|
t****t
发帖数: 6806 | 15 no, 我问的不是你在LAN里用WAN的IP访问, 而是真的从WAN访问, 比如说这么设置
(192.168.10.1)
router B (LAN)---- computer C (192.168.10.2)
(LAN)
|
|
(WAN) (192.168.10.3)
router A
(LAN) (192.168.2.1) (不用)
这个设置下, 你能用C访问A的web gui吗?
modem
Host Table of the
还是不成。俺也是EE的技术民工。不过不是专稿网络的。实在没辙了，才来求教高手。
directly
【在 d*******n 的大作中提到】
: 我在家里（LAN）上可以用DDNS或WAN的裸IP带着port访问。no problem. 但是一用外网
: ，就好象用东西塞住了似的。刷好几遍才能load一部分GUI。我刚才又研究了一下modem
: .把它设成了真正的NAT Passthru. 现在Router A is listed on the Passthrough Host Table of the
: modem. 按照以下的定义现在modem真是modem only了。我也看不到router A在modem上
: IP了。modem也显示DHCP disabled 了. 这样Router A 实际上直接和ISP接吻了。可还是不成。俺也是EE的技术民工。不过不是专稿网络的。实在没辙了，才来求教高手。
: These are bridged CPEs, that have obtained their public IP address directly
: from the DHCP server on your ISPs network, and are not using any form of
: address translation.
: 先从10个包子。辛苦辛苦。
|
d*******n
发帖数: 369 | 16 hehe, 我一般在技术贴里不说人怎样。也不理会别人说我的话。免得变成掐架。对了我
是用tomato 1.28 shibby build.会不会和这个有关？有没有人用tomato的用remote
admin GUI?
【在 t****t 的大作中提到】
: 这个倒不是他网盲, 现在的DMZ都是这么设置的. 你out了.
:
: -
: .
|
d*******n
发帖数: 369 | 17 你的意思是说从LAN的另一个subnet(192.168.10.x)通过WAN去访问？我没试过。只试过
从我office里访问不行。with my office, it's like
my office PC (10.10.10.222) ----
(LAN)
office router/gateway
(WAN)
|
|
(WAN) (75.x.x.x from comcast DHCP)
router A
(LAN) (192.168.2.1) --- my home pc, printer...
【在 t****t 的大作中提到】
: no, 我问的不是你在LAN里用WAN的IP访问, 而是真的从WAN访问, 比如说这么设置
: (192.168.10.1)
: router B (LAN)---- computer C (192.168.10.2)
: (LAN)
: |
: |
: (WAN) (192.168.10.3)
: router A
: (LAN) (192.168.2.1) (不用)
: 这个设置下, 你能用C访问A的web gui吗?
|
a*****3
发帖数: 1545 | 18 大哥，100包子是1000伪币，不是100伪币 |
t****t
发帖数: 6806 | 19 i never used that build, and i don't use remote admin gui. i have another
server with ssh opened behind router, and if i need to access router, i will
ssh again from that server.
【在 d*******n 的大作中提到】
: hehe, 我一般在技术贴里不说人怎样。也不理会别人说我的话。免得变成掐架。对了我
: 是用tomato 1.28 shibby build.会不会和这个有关？有没有人用tomato的用remote
: admin GUI?
|
