I******t 发帖数: 829 | 1 算是BSO贴吧,欢迎拍砖。先发图,明天再加简介。 |
I******t 发帖数: 829 | 2 续图
【在 I******t 的大作中提到】 : 算是BSO贴吧,欢迎拍砖。先发图,明天再加简介。
|
I******t 发帖数: 829 | 3 续图二
【在 I******t 的大作中提到】 : 续图
|
t******p 发帖数: 25 | |
I******t 发帖数: 829 | 5 大概10小时,锯角钢、上上下下爬梯子浪费不少时间。
【在 t******p 的大作中提到】 : 赞! 花了多长时间?
|
f********l 发帖数: 1473 | |
c********h 发帖数: 7827 | |
Y********e 发帖数: 2445 | |
d*****i 发帖数: 163 | |
I******t 发帖数: 829 | 10 补充的简介,有些啰嗦。
第一, 选购opener。根据自家车库门的大小选择opener,通常1/2 horsepower的
opener足够家庭车库。我选Chamberlain的,适于DIY,各店都有卖。比较价格后,
Lowes有特价便宜$30,加上10%的哭胖(邮局要来的change address package内有),
一共省了$50。Lowes 和homedepot都管安装,要$97,但要$35先inspect,还不管电路
,如果自己加电路,必须符合他们的code。俺自个喜欢鼓捣这些,就决定自己干了。
第二, 要做计划。根据车库现状找到安装opener两端的位置,motor要挂在梁上,
车门一端要安到车门上方15cm以上。俺家门上方是空心砖(见图1),直接安装不牢固
,要加块2x6(图5)。另外需要角钢固定motor(图4),以及各种工具(图3)。这
么多工具,每个都有大用处。
第三, 装电路。电路和电源须自备,电源必须距离motor不超过3ft。不多废话了,
见图6, 7, 8。
第四, 装2x6,图9。
第五, 照着手册装opener,moto |
|
|
g*****9 发帖数: 4125 | 11
You need a cut off saw (only take a few second to cut)
上上下下爬梯子浪费不少时间。
I usually build a wooden platform and walk up ramp first with some 2x4 and
plywood, maybe 20 min with if you have nailer. Much safer to walk around.
and you can take it apart use it next time.
【在 I******t 的大作中提到】 : 大概10小时,锯角钢、上上下下爬梯子浪费不少时间。
|
k***e 发帖数: 7933 | 12 很handy啊。
你这个车库原来没有opener吗?是换还是新装的?
【在 I******t 的大作中提到】 : 补充的简介,有些啰嗦。 : 第一, 选购opener。根据自家车库门的大小选择opener,通常1/2 horsepower的 : opener足够家庭车库。我选Chamberlain的,适于DIY,各店都有卖。比较价格后, : Lowes有特价便宜$30,加上10%的哭胖(邮局要来的change address package内有), : 一共省了$50。Lowes 和homedepot都管安装,要$97,但要$35先inspect,还不管电路 : ,如果自己加电路,必须符合他们的code。俺自个喜欢鼓捣这些,就决定自己干了。 : 第二, 要做计划。根据车库现状找到安装opener两端的位置,motor要挂在梁上, : 车门一端要安到车门上方15cm以上。俺家门上方是空心砖(见图1),直接安装不牢固 : ,要加块2x6(图5)。另外需要角钢固定motor(图4),以及各种工具(图3)。这 : 么多工具,每个都有大用处。
|
B*******O 发帖数: 543 | |
I******t 发帖数: 829 | 14 cutoff saw = circle saw? I have a circle saw, but can only use it to cut
wood.
你的平台一般有多大?我要在车库内来回走,这个平台要很大吧?大的平台要保证稳固
,要很好的结构设计吧?我没干过,您有图纸可以share吗?
【在 g*****9 的大作中提到】 : : You need a cut off saw (only take a few second to cut) : 上上下下爬梯子浪费不少时间。 : I usually build a wooden platform and walk up ramp first with some 2x4 and : plywood, maybe 20 min with if you have nailer. Much safer to walk around. : and you can take it apart use it next time.
|
I******t 发帖数: 829 | 15 谢谢,是新装的。
【在 k***e 的大作中提到】 : 很handy啊。 : 你这个车库原来没有opener吗?是换还是新装的?
|
m*******r 发帖数: 2044 | 16 看了的不要随便学,我知道一个把指头上的肉切下一块的,就是链条部分。 |
g*****9 发帖数: 4125 | 17
No. They look similar, but not the same.
Cutoff saw or metal chop saw, is a power tool which is typically used to cut
hard materials, such as metals. The cutting action is performed by an
abrasive disc, similar to a thin grinding wheel. The saw generally has a
built-in vise or other clamping arrangement, and has the cutting wheel and
motor mounted on a pivoting arm attached to a fixed base plate.
They typically use composite friction disk blades to abrasively cut through
the steel. The disks ar
【在 I******t 的大作中提到】 : cutoff saw = circle saw? I have a circle saw, but can only use it to cut : wood. : 你的平台一般有多大?我要在车库内来回走,这个平台要很大吧?大的平台要保证稳固 : ,要很好的结构设计吧?我没干过,您有图纸可以share吗?
|
I******t 发帖数: 829 | 18 严重同意,很多步骤操作不当都有危险。其实我的这个DIY省不了多少钱,工时太长
,10小时。请专业工人应该不超过$300,包括电路部分。
【在 m*******r 的大作中提到】 : 看了的不要随便学,我知道一个把指头上的肉切下一块的,就是链条部分。
|
I******t 发帖数: 829 | 19 学习了,以后别的项目可以试试。
cut
through
【在 g*****9 的大作中提到】 : : No. They look similar, but not the same. : Cutoff saw or metal chop saw, is a power tool which is typically used to cut : hard materials, such as metals. The cutting action is performed by an : abrasive disc, similar to a thin grinding wheel. The saw generally has a : built-in vise or other clamping arrangement, and has the cutting wheel and : motor mounted on a pivoting arm attached to a fixed base plate. : They typically use composite friction disk blades to abrasively cut through : the steel. The disks ar
|
t*****m 发帖数: 254 | 20 Did you reinforce the garage-door panel where the pull-bracket is mounted
to? By looking at the picture, seems your mount the bracket on to the door
directly. Over the time, the screws may come loose if the door is steel.
【在 I******t 的大作中提到】 : 学习了,以后别的项目可以试试。 : : cut : through
|
R**R 发帖数: 3318 | 21 严重同意,很多步骤操作不当都有危险。
DIY不光是为了省钱,主要是方便。这次虽然干了10小时,实际是学习了10小时。下次
干别的,会有更好的sense.
【在 I******t 的大作中提到】 : 严重同意,很多步骤操作不当都有危险。其实我的这个DIY省不了多少钱,工时太长 : ,10小时。请专业工人应该不超过$300,包括电路部分。
|
I******t 发帖数: 829 | 22 The door is steel. I didn't reinforce yet. Thanks for reminding. Is it ok to
reinforce when the screws is getting loose?
【在 t*****m 的大作中提到】 : Did you reinforce the garage-door panel where the pull-bracket is mounted : to? By looking at the picture, seems your mount the bracket on to the door : directly. Over the time, the screws may come loose if the door is steel.
|