o*e
发帖数: 1304 | 1 试图开门或者关门，opener还是有持续的声音发出，如果不再按一下控制器，会一直响
下去。但门却不动。也就是那个链条根本没在动。
可以排除不是sensor的问题（确定没东西在sensor之间，亮灯也正常），也不是扭力的
问题（已经试过调到最大了）
有人知道该怎么办么？谢谢！ |
p*****p
发帖数: 19331 | 2 齿轮滑丝了，换齿轮，看youtube
或者，整个机器换掉，如果机器很老的话 |
w*******g
发帖数: 9932 | 3 replace the whole thing
cheap
one day job diy
【在 o*e 的大作中提到】
: 试图开门或者关门，opener还是有持续的声音发出，如果不再按一下控制器，会一直响
: 下去。但门却不动。也就是那个链条根本没在动。
: 可以排除不是sensor的问题（确定没东西在sensor之间，亮灯也正常），也不是扭力的
: 问题（已经试过调到最大了）
: 有人知道该怎么办么？谢谢！
|
p****j
发帖数: 4762 | |
u****q
发帖数: 24345 | 5 RE
把chain-driven的换成belt-driven的，超级安静。
【在 w*******g 的大作中提到】
: replace the whole thing
: cheap
: one day job diy
|
w*******g
发帖数: 9932 | 6 Belt drive is quiet/expensive but your garage door is another source of
noise. Chain drive can be quiet if you install it correctly.
【在 u****q 的大作中提到】
: RE
: 把chain-driven的换成belt-driven的，超级安静。
|
o*e
发帖数: 1304 | 7 拆开来看了，的确是，准备买个换上试试。谢谢
【在 p*****p 的大作中提到】
: 齿轮滑丝了，换齿轮，看youtube
: 或者，整个机器换掉，如果机器很老的话
|
o*e
发帖数: 1304 | 8 Whole thing 是说把整个opener和链条都换掉？
【在 w*******g 的大作中提到】
: replace the whole thing
: cheap
: one day job diy
|
w*******g
发帖数: 9932 | 9 right. Replace everything. Drive, opener, sensor.
I did it for my garage a few months ago and it is not hard but takes time.
The opener is around 200 dollars.
It is a one person job but if your wife can help you, it is a little easier.
I got the same problem as yours and replacing parts cost 40 bucks and I have
to take off the opener as well.
The most time consuming part turns out to be routing the wires for sensor
and opener. I don't have a staple gun and removing old wire takes time as
well since I don't want to pull the whole thing out.
【在 o*e 的大作中提到】
: Whole thing 是说把整个opener和链条都换掉？
|
o*e
发帖数: 1304 | 10 谢谢， 我先试试换gear吧。
easier.
have
【在 w*******g 的大作中提到】
: right. Replace everything. Drive, opener, sensor.
: I did it for my garage a few months ago and it is not hard but takes time.
: The opener is around 200 dollars.
: It is a one person job but if your wife can help you, it is a little easier.
: I got the same problem as yours and replacing parts cost 40 bucks and I have
: to take off the opener as well.
: The most time consuming part turns out to be routing the wires for sensor
: and opener. I don't have a staple gun and removing old wire takes time as
: well since I don't want to pull the whole thing out.
|
