c******n 发帖数: 4965 | 1 would you recommend using ramps or jacks + stands? price seems the same
what do u use to hold the old oil? on way to dump it at autozone, I don't
want the oil to spill in my car |
n****e 发帖数: 6292 | 2 ramp方便很多
可以用那种可以封口的drop pan,或者把旧油灌到倒空的新油瓶子里去 |
y****n 发帖数: 798 | 3 一般的ramp很容易滑下去, 而且不容易控制, 如果底盘低的比如m3, s2000一般的
ramp根本就上不去, 得用race ramp
我在用costco的3.5t的jack+stands, 碰上底盘低的, 先开上低一点的木头, 再用
floor jack支起来就行了, 就是costco卖的那个玩意快一百磅了, 每次搬的时候可是
力气活
【在 c******n 的大作中提到】 : would you recommend using ramps or jacks + stands? price seems the same : what do u use to hold the old oil? on way to dump it at autozone, I don't : want the oil to spill in my car
|
c******n 发帖数: 4965 | 4 http://www.costco.com/Browse/Product.aspx?Prodid=11590524&searc
this? this says 2-ton though
I'm planning to buy a 3-ton jack+stands, since I want to do some basic oil
change now, but after I buy a house, I'll buy a F150 to play with, so need a
big jack for that.
japanese cars normally use metric sizes, right? F150 use SAE? any
recommendations for sockets/ratchets sets ?
this looks a good one
http://www.amazon.com/Torin-T83536-Service-Jack-Stand/dp/B0001E
【在 y****n 的大作中提到】 : 一般的ramp很容易滑下去, 而且不容易控制, 如果底盘低的比如m3, s2000一般的 : ramp根本就上不去, 得用race ramp : 我在用costco的3.5t的jack+stands, 碰上底盘低的, 先开上低一点的木头, 再用 : floor jack支起来就行了, 就是costco卖的那个玩意快一百磅了, 每次搬的时候可是 : 力气活
|
D*******a 发帖数: 3688 | 5 if someday you need to take off the wheels (e,g, change brakes), ramps will
be useless.
【在 c******n 的大作中提到】 : would you recommend using ramps or jacks + stands? price seems the same : what do u use to hold the old oil? on way to dump it at autozone, I don't : want the oil to spill in my car
|
c**d 发帖数: 3888 | 6 I've used both and my advice is this -- Use ramps if your car sits very low
or is otherwise hard to jack up. If not, use floor jack + stands |
f********r 发帖数: 3155 | 7 这个要赞
will
【在 D*******a 的大作中提到】 : if someday you need to take off the wheels (e,g, change brakes), ramps will : be useless.
|
e**o 发帖数: 5509 | 8 2 ton就够了吧。F150 总共就重2吨多点。
也不是用jack把车都托起来,每次托一侧,估计都不到2/3的车重。
a
【在 c******n 的大作中提到】 : http://www.costco.com/Browse/Product.aspx?Prodid=11590524&searc : this? this says 2-ton though : I'm planning to buy a 3-ton jack+stands, since I want to do some basic oil : change now, but after I buy a house, I'll buy a F150 to play with, so need a : big jack for that. : japanese cars normally use metric sizes, right? F150 use SAE? any : recommendations for sockets/ratchets sets ? : this looks a good one : http://www.amazon.com/Torin-T83536-Service-Jack-Stand/dp/B0001E
|