c*u 发帖数: 916 | 1 我需要解决一个问题,似乎不会太复杂,但是我水平不够,所以请教各位高手,
我有一段SMF-28光纤,其cut-off波长是1250 nm左右,所以1250nm更长的光在其中可以
当作single-mode。这个光纤的末端,我加了一个lens,因为是single mode,所以其聚
焦特性很容易用Gaussian beam理论来研究。
但是我现在需要把一束绿光(532nm)的光导入该光纤,然后研究其聚焦特性,查了一
下一些光学的入门书,好像最多也就是研究其在光纤中的Laguerre-Gaussian modes,
没有说明怎么对这种multi-mode光的聚焦计算,尤其是怎么用ABCD来计算。大牛们能告
诉我这东西如何入手么? | R****a 发帖数: 199 | 2 I guess the calculation is not easy. The reason is as following:
Your fiber is not single mode fiber for 532nm light for sure, but it is not
quite 'multi-mode' either. The core is small and the contrast is not that
large, it may be just a few modes. You can use a software or even use simple
scalor method to estimate how many modes supported.
But even you know how many modes are supported, you still cannot get much
information from this one. Since the fiber you used may be pretty long, the
mode p
【在 c*u 的大作中提到】 : 我需要解决一个问题,似乎不会太复杂,但是我水平不够,所以请教各位高手, : 我有一段SMF-28光纤,其cut-off波长是1250 nm左右,所以1250nm更长的光在其中可以 : 当作single-mode。这个光纤的末端,我加了一个lens,因为是single mode,所以其聚 : 焦特性很容易用Gaussian beam理论来研究。 : 但是我现在需要把一束绿光(532nm)的光导入该光纤,然后研究其聚焦特性,查了一 : 下一些光学的入门书,好像最多也就是研究其在光纤中的Laguerre-Gaussian modes, : 没有说明怎么对这种multi-mode光的聚焦计算,尤其是怎么用ABCD来计算。大牛们能告 : 诉我这东西如何入手么?
| c*u 发帖数: 916 | 3 Fiber当然是不能换的,要不然这个问题就过分简单了:-) 我必须用SMF-28光纤,因为我
在公司,有很多别的人需要把那个光纤弄成smf-28。
多少个mode可以很容易计算,到底有哪些mode可以列举出来,甚至这些mode的分布也可
以计算出来。我所不明白的是,
1。对于这些mode经过透镜后,怎么计算,怎么用ABCD matrix或者其他办法。这样我至
少可以计算worst case scenario,
2。正如同你所说,比如有5个mode,这5个mode不见得光强度一样,这种mode间的
leakage和最后分布与光纤长度和弯曲度显然有关。显然不定态是很难弄的,有什么办
法保证大致上只在一个mode,或者全部均匀分布?
xiexie,
not
simple
the
【在 R****a 的大作中提到】 : I guess the calculation is not easy. The reason is as following: : Your fiber is not single mode fiber for 532nm light for sure, but it is not : quite 'multi-mode' either. The core is small and the contrast is not that : large, it may be just a few modes. You can use a software or even use simple : scalor method to estimate how many modes supported. : But even you know how many modes are supported, you still cannot get much : information from this one. Since the fiber you used may be pretty long, the : mode p
| R****a 发帖数: 199 | 4 1。对于这些mode经过透镜后,怎么计算,怎么用ABCD matrix或者其他办法。这样我至
少可以计算worst case scenario,
You can do this for each mode. For the fundamental mode, you can make the
assumption that the mode shape is a Gaussian, then ABCD matrix works. For
higher order mode, I would say if the order goes up, the error goes up too.
(And ABCD matrix still works.)
http://www.newport.com/servicesupport/Tutorials/default.aspx?id=112
2。正如同你所说,比如有5个mode,这5个mode不见得光强度一样,这种mode间的
leakage和最后分布与光纤长度和弯曲度显然有关。显然不定态是很难弄的,有什么办
法保证大致上只在一个mode,或者全
【在 c*u 的大作中提到】 : Fiber当然是不能换的,要不然这个问题就过分简单了:-) 我必须用SMF-28光纤,因为我 : 在公司,有很多别的人需要把那个光纤弄成smf-28。 : 多少个mode可以很容易计算,到底有哪些mode可以列举出来,甚至这些mode的分布也可 : 以计算出来。我所不明白的是, : 1。对于这些mode经过透镜后,怎么计算,怎么用ABCD matrix或者其他办法。这样我至 : 少可以计算worst case scenario, : 2。正如同你所说,比如有5个mode,这5个mode不见得光强度一样,这种mode间的 : leakage和最后分布与光纤长度和弯曲度显然有关。显然不定态是很难弄的,有什么办 : 法保证大致上只在一个mode,或者全部均匀分布? : xiexie,
| b******g 发帖数: 77 | 5 高斯光束经过成像还是高斯光束,把高斯光束的分布和光纤中的模式做交叠积分,就可
以算各个模式所占比例 |
|