A****h 发帖数: 1486 | 1 【 以下文字转载自 PhotoGear 讨论区 】
发信人: Asmith (四轮曲), 信区: PhotoGear
标 题: 我悲剧了,宁断了lug nut
发信站: BBS 未名空间站 (Fri Mar 19 19:16:15 2010, 美东)
拿不出来鸟,那里可以帮着拿出来?
难道明天去dealer问? |
p****r 发帖数: 766 | 2 拿锤子砸出来就行了。LUG NUT也就一两块钱一个。 |
A****h 发帖数: 1486 | 3 The other half is still on the bolt.
How to take it off ?
See this post for pictures
http://www.mitbbs.com/article/PhotoGear/32045435_0.html
【在 p****r 的大作中提到】 : 拿锤子砸出来就行了。LUG NUT也就一两块钱一个。
|
LC 发帖数: 748 | |
p****b 发帖数: 281 | 5 这我也干过,你把rotor卸下来,拿锤子就可以砸出来了 |
N*****N 发帖数: 238 | 6 找shop吧,他们干很容易的,焊个螺帽上去就行了
【在 p****b 的大作中提到】 : 这我也干过,你把rotor卸下来,拿锤子就可以砸出来了
|
N*****N 发帖数: 238 | 7 找shop吧,他们干很容易的,焊个螺帽上去就行了
【在 p****b 的大作中提到】 : 这我也干过,你把rotor卸下来,拿锤子就可以砸出来了
|
c******k 发帖数: 1089 | 8 我觉得你拧断是cover,不是nut.
我严重怀疑你什么力气能拧断真正的lug nut.
是不是第一次拧车轮nut?
你很可能还没看见nut,就开始拧了。
应该先把外表光亮的那个用pry bar给翘下来,然后才能看见nut.
【在 A****h 的大作中提到】 : 【 以下文字转载自 PhotoGear 讨论区 】 : 发信人: Asmith (四轮曲), 信区: PhotoGear : 标 题: 我悲剧了,宁断了lug nut : 发信站: BBS 未名空间站 (Fri Mar 19 19:16:15 2010, 美东) : 拿不出来鸟,那里可以帮着拿出来? : 难道明天去dealer问?
|
A****h 发帖数: 1486 | 9 嗯,昨天换过6块扎啤的说。
【在 c******k 的大作中提到】 : 我觉得你拧断是cover,不是nut. : 我严重怀疑你什么力气能拧断真正的lug nut. : 是不是第一次拧车轮nut? : 你很可能还没看见nut,就开始拧了。 : 应该先把外表光亮的那个用pry bar给翘下来,然后才能看见nut.
|
c******k 发帖数: 1089 | 10 什么意思? 真的是lug nut? 那你就太有力气了,我只拧断过10mm的bolt.
【在 A****h 的大作中提到】 : 嗯,昨天换过6块扎啤的说。
|
|
|
d*b 发帖数: 21830 | 11 考,你知道lug nut是什么么?
【在 N*****N 的大作中提到】 : 找shop吧,他们干很容易的,焊个螺帽上去就行了
|
d*b 发帖数: 21830 | 12 我老至少拧断过不下20个Lug nut了,拧断lug nut不很常见?
【在 c******k 的大作中提到】 : 我觉得你拧断是cover,不是nut. : 我严重怀疑你什么力气能拧断真正的lug nut. : 是不是第一次拧车轮nut? : 你很可能还没看见nut,就开始拧了。 : 应该先把外表光亮的那个用pry bar给翘下来,然后才能看见nut.
|
d*b 发帖数: 21830 | 13 2块钱的东西悲剧个屁啊,去autozone买一个lug nut,把rotor拆下来一榔头就敲出来了。
【在 A****h 的大作中提到】 : 嗯,昨天换过6块扎啤的说。
|
p****r 发帖数: 766 | 14 把车顶起来,把钴轳卸下来,卸下刹车CALIPER,ROTOR,从里面往外用锤子砸出来就行
了 -- 需要使用一些力气。有的车带一个小卡片,把卡片撬掉(卡片没什么用的 -- 是
工厂方便组装用的东西)。 |
A****h 发帖数: 1486 | 15 不卸轮子,rotor 怎么写下来?
了。
【在 d*b 的大作中提到】 : 2块钱的东西悲剧个屁啊,去autozone买一个lug nut,把rotor拆下来一榔头就敲出来了。
|
A****h 发帖数: 1486 | 16 那个碎掉的nut还在stud上,弄不下来。
怎么不拆轮子就把rotor写下来呢?
【在 p****r 的大作中提到】 : 把车顶起来,把钴轳卸下来,卸下刹车CALIPER,ROTOR,从里面往外用锤子砸出来就行 : 了 -- 需要使用一些力气。有的车带一个小卡片,把卡片撬掉(卡片没什么用的 -- 是 : 工厂方便组装用的东西)。
|
q***t 发帖数: 59 | 17 后来如何?
还有, 楼主这个问题怎么没人回了? dsb 呢?
【在 A****h 的大作中提到】 : 那个碎掉的nut还在stud上,弄不下来。 : 怎么不拆轮子就把rotor写下来呢?
|
A****h 发帖数: 1486 | 18 sent to tireshop and they can't handle it. Have to wait monday or tuesday.
The mechanics will probably find the right tool to untwist it.
【在 q***t 的大作中提到】 : 后来如何? : 还有, 楼主这个问题怎么没人回了? dsb 呢?
|
q***t 发帖数: 59 | 19 pls let us know how they handle it.
螺丝拧断了好办,你这个是挺难的, 不过从照片上看, 你那个nut好象有点薄
【在 A****h 的大作中提到】 : sent to tireshop and they can't handle it. Have to wait monday or tuesday. : The mechanics will probably find the right tool to untwist it.
|
e*******0 发帖数: 367 | |
|
|
A****h 发帖数: 1486 | 21 All season, same as the old ones. The old ones don't have much thread
left.
【在 e*******0 的大作中提到】 : 你的ls430换summer tire?
|
f**y 发帖数: 138 | 22 How about try the following:
1. Loose all other nuts on the same wheel to reduce the pressure on this
broken nut.
2. Add WD-40 or other stronger liquid wrench on the broken nut.
3. Try to turn the broken nut counter clockwise with a pair of pliers.
4. If it doesn't work, try to cut a slit on the cylinder of the broken nut
with a Dremel drill. Insert a piece of flat metal into the slit, and turn it
with a pair of pliers.
5. If it still doesn't work, drill away the stud with a drill bit at the
siz |
A****h 发帖数: 1486 | 23 WOW, wow. These are very valuable advices, I will try them before I send it
back to garage again.
A question for advice 1: I think tighten up the rest of the nuts might help
to get the broken nut off since the cause of the broken nut was a stupid
clockwise turn...
I will try to drill some nick on the broken nut, but broken nut does not
have a perfect surface for drilling when it broke.
You must be a pro in car repair.
it
【在 f**y 的大作中提到】 : How about try the following: : 1. Loose all other nuts on the same wheel to reduce the pressure on this : broken nut. : 2. Add WD-40 or other stronger liquid wrench on the broken nut. : 3. Try to turn the broken nut counter clockwise with a pair of pliers. : 4. If it doesn't work, try to cut a slit on the cylinder of the broken nut : with a Dremel drill. Insert a piece of flat metal into the slit, and turn it : with a pair of pliers. : 5. If it still doesn't work, drill away the stud with a drill bit at the : siz
|
l******d 发帖数: 54 | 24 Buy a power tool called Angle Grinder. About $15 at O'Reilly. Cut the brokrn
nut off, and replace with a new set about $4. Take 1-2 hours.
http://shop.oreillyauto.com/ProductDetail.aspx?MfrCode=BFT&MfrPartNumber=CO412PBX&CategoryCode=3574 |
A****h 发帖数: 1486 | 25 Good idea, but won't fit my case. The nut is at the parigee of the stud hole
.
See the pictures I posted before. I don't think it will be able to reach it
without damaging the wheel.
brokrn
【在 l******d 的大作中提到】 : Buy a power tool called Angle Grinder. About $15 at O'Reilly. Cut the brokrn : nut off, and replace with a new set about $4. Take 1-2 hours. : http://shop.oreillyauto.com/ProductDetail.aspx?MfrCode=BFT&MfrPartNumber=CO412PBX&CategoryCode=3574
|
s**********d 发帖数: 36899 | 26 别听这些人瞎编了。你那个在洞里,他们说的根本都没法办。
还有人说用钳子,搞笑吗,上一尺多长的wrench都是用脚踹。
你的唯一方法就是用钻把那个lug钻了。钻到nut松动能下来
就行了,然后轮子卸掉敲掉lug换个新的。 |
A****h 发帖数: 1486 | 27 That's the ultimate measurement for this case, otherwise, I will try this
before I use the drill.
http://www.brandsport.com/ctam-a155.html
【在 s**********d 的大作中提到】 : 别听这些人瞎编了。你那个在洞里,他们说的根本都没法办。 : 还有人说用钳子,搞笑吗,上一尺多长的wrench都是用脚踹。 : 你的唯一方法就是用钻把那个lug钻了。钻到nut松动能下来 : 就行了,然后轮子卸掉敲掉lug换个新的。
|
s**********d 发帖数: 36899 | 28 这种东西不咋好用。用的话提前一天就用pb blaster泡那个断的nut,
下的时候用impact wrench。
this
【在 A****h 的大作中提到】 : That's the ultimate measurement for this case, otherwise, I will try this : before I use the drill. : http://www.brandsport.com/ctam-a155.html
|
Z*****o 发帖数: 4090 | 29 看了题目,我在想,有什么比拧断了螺母更痛苦的,要宁愿。。。
原来是通假字。 |
l******d 发帖数: 54 | 30 I don't see your pic and don't know much about your case. In my case, after
taking off the good nuts, I pulled the wheel cover off by using a little bit
of muscle.Then it was easy to reach. My suggestion is do not try the drill
thing, unless you have a so powerful drill and bits. Good luck!
hole
it
【在 A****h 的大作中提到】 : Good idea, but won't fit my case. The nut is at the parigee of the stud hole : . : See the pictures I posted before. I don't think it will be able to reach it : without damaging the wheel. : : brokrn
|
|
|
l******d 发帖数: 54 | 31 I doubt this measurement, since I guess, in your case, the broken part is
the inside thread of the stud.
【在 A****h 的大作中提到】 : That's the ultimate measurement for this case, otherwise, I will try this : before I use the drill. : http://www.brandsport.com/ctam-a155.html
|
A****h 发帖数: 1486 | 32 去了以前修好前bumper的修车铺,大概花了5分钟把问题解决了。先试了试六角套筒扳
手,结果不行。
后来用铁锥子把那剩下的一段硬硬凿碎了,换了新的螺帽,没charge钱。
特地赞一下RP,敢着下回去拎一箱啤酒去感谢,呵呵。 |