G***G 发帖数: 16778 | 1 anyone has the same feeling as me?
a little bit tired of removing the tire each time when you do it.
dream to buy a set of electronic impact wrench for this purpose.
but there are two reasons that let you stop the dream.
1) a good set of the electronic impact wrench is nearly $400.
If you buy a $100 one, it is garbage.
2) most of times, the set of electronic impact wrench will sit in your
garage
for whole years. Absolutely, you don't want to use it monthly, which means
your car gets a big problem.
3) when you install wheels, how do you avoid not tightening the nug lut too
much
when you use the electronic impact wrench? |
h******u 发帖数: 389 | 2 你是不是打算diy?是就买,400不算多,两三次diy就回来了 |
G***G 发帖数: 16778 | 3 thank you for understanding my situation.
I am also waiting for the deal. If it can go down to $300, I will buy one
set.
The one I want to buy has maximum torque of 1100 ft-pound.
I think it can remove the crankshaft nut.
【在 h******u 的大作中提到】 : 你是不是打算diy?是就买,400不算多,两三次diy就回来了
|
G********1 发帖数: 1341 | 4 如果打算DIY,imapct 还是需要的,像楼上说的几次价钱就回来了。以后不用了,考虑
二手卖掉。
3)如果 impact 不能设定,上轮子就手动,用 torque wrench 或 breaker bar。 |
f*****h 发帖数: 4489 | 5 我也打算diy, 用手动的 3个月一次无所谓 当锻炼身体
【在 G***G 的大作中提到】 : anyone has the same feeling as me? : a little bit tired of removing the tire each time when you do it. : dream to buy a set of electronic impact wrench for this purpose. : but there are two reasons that let you stop the dream. : 1) a good set of the electronic impact wrench is nearly $400. : If you buy a $100 one, it is garbage. : 2) most of times, the set of electronic impact wrench will sit in your : garage : for whole years. Absolutely, you don't want to use it monthly, which means : your car gets a big problem.
|
g***n 发帖数: 14250 | 6 就卸轮子,harborfreight 那个 230ft-lbs 的足够用了,才70 块吧 |
G********1 发帖数: 1341 | 7 如果考虑卸驱动轴的话,330ft-lbs 的保险些。
【在 g***n 的大作中提到】 : 就卸轮子,harborfreight 那个 230ft-lbs 的足够用了,才70 块吧
|
e**n 发帖数: 5876 | |
l****g 发帖数: 5080 | 9 算上各种减价券,超过45刀就贵了。但是想做的时候有工具帮忙,priceless。不过我
用这个轮换了一次轮胎,以后都是找苦胖带免费轮换轮胎的,因为自己用千斤顶顶来顶
去的也挺费力,又不能买个修车铺的那种把车整体提升的机器。
【在 g***n 的大作中提到】 : 就卸轮子,harborfreight 那个 230ft-lbs 的足够用了,才70 块吧
|
G***G 发帖数: 16778 | 10 cool. which is better, craftsman 350 vs harbor freight 238?
【在 e**n 的大作中提到】 : 几个月前craftsman 350的才$50
|
|
|
G***G 发帖数: 16778 | 11 你说的换轮胎,是不是换上新轮胎?
“免费轮换轮胎”是什么意思? 是指把前后轮对换吗?
我昨天就干了这个前后轮对换,累得两条腿抬不起来了。奇怪,明明是用胳膊扳轮子,
结果疼的是大腿。另外,前后同时jack stands,好危险。差点掉下来了。
【在 l****g 的大作中提到】 : 算上各种减价券,超过45刀就贵了。但是想做的时候有工具帮忙,priceless。不过我 : 用这个轮换了一次轮胎,以后都是找苦胖带免费轮换轮胎的,因为自己用千斤顶顶来顶 : 去的也挺费力,又不能买个修车铺的那种把车整体提升的机器。
|
h******u 发帖数: 389 | 12 前后换个轮胎就累坏了。。。。算了你不适合diy,还是别花钱买工具了 |
D********d 发帖数: 2154 | 13 换雪胎轮韝,也就1小时。
用 torque wrench 手动足以。 |
g***n 发帖数: 14250 | 14 有没有卖四个 floor jack 用一个把手联动一起顶起来的,那简直是 rotate 神器啊
【在 l****g 的大作中提到】 : 算上各种减价券,超过45刀就贵了。但是想做的时候有工具帮忙,priceless。不过我 : 用这个轮换了一次轮胎,以后都是找苦胖带免费轮换轮胎的,因为自己用千斤顶顶来顶 : 去的也挺费力,又不能买个修车铺的那种把车整体提升的机器。
|
l****g 发帖数: 5080 | 15 你的这个没做对, 在架起来以前用力把螺丝拧松, 上紧螺丝也是车落地以后再使力上紧
,这样才安全。
【在 G***G 的大作中提到】 : 你说的换轮胎,是不是换上新轮胎? : “免费轮换轮胎”是什么意思? 是指把前后轮对换吗? : 我昨天就干了这个前后轮对换,累得两条腿抬不起来了。奇怪,明明是用胳膊扳轮子, : 结果疼的是大腿。另外,前后同时jack stands,好危险。差点掉下来了。
|
l****g 发帖数: 5080 | 16 一个小时也挺累, 有换油顺带免费rotation的当然更划算。
【在 D********d 的大作中提到】 : 换雪胎轮韝,也就1小时。 : 用 torque wrench 手动足以。
|
E****a 发帖数: 3088 | |